Makers of precision Cue Smith™ brand cue lathes and inlay machine
 
Home  -  About Us  -  Contact Us  -  Testimonies  -  Tell A Friend
Subscribe to our
E-letter for tips, updates on our site, specials, new products, and more!


Enter your email address below and click Subscribe.

 

 

 

 

cue smith cue lathe slogan
Cue Man Billard Products :: Accessories : Lathe Supplies :: Makers of the Precise Cue Smith Cue Lathes and Inlay Machine, billiard supplies, and accessories
Lathe Supplies
ORDERING INFORMATION:
When ordering please call Chris Hightower to place the order. Buyer pays all shipping and handling. SORRY NO C.O.D. ORDERS ON LATHES. Advance payment with cashiers check or money order is required on lathes and high $$ orders. We will C.O.D. most accessories and parts. We accept Credit Cards and Pay Pal for smaller orders. Make checks and money orders out to: CUE MAN BILLIARDS
See "Contact Us" link for address and phone number!
QUICK CHANGE TOOLPOST with 2 square tool, 1 boring bar and 1 cut off tool holders. Extra tool holders $30 each or 4 for $25 each..
$135

BED EXTENSION for any Cue Smith Lathe, will snap on and off either end of the lathe. Use with house steady rest for doing one piece cues!

$125 each

HOUSE CUE STEADY REST (Cue Smith Type)

$95 each

DIAL CALIPERS- .001 -6" (for checking diameters)

DIAL INDICATOR 1 mounts on cross-slide or carriage for checking run out, setting up taper bars and cutting exact diameters.

DIAL INDICATOR 2 mounts to bed next to carriage for cutting rings, butt plates and boring holes to exact lengths.

$35 each

$40 each

$50 each

CUE BUILDING BOOK (260+ pages , completely illustrated)  3rd edition    (See Book and Videos Page for special offers)

$69.95 each

CUE BUILDING and REPAIR VIDEO (2.5 Hours VHS or DVD)
$50 each

ADVANCED CUE BUILDING VIDEO Volume One (Points and Inlays- almost 3 Hours DVD)

ADVANCED CUE BUILDING VIDEO Volume Two (Cue Assembly, Boring, Coring, Tenons and more- Almost 2.5 Hours DVD)

CUE FINISHING MADE SIMPLE VIDEO (Cue Cote Epoxy, Super Glue, and Water Based Urethane Finishing, Re-Finishing, Carbide Sanding Mandrels, Brushing and Spraying Methods!- Almost 3 hours DVD)

SEE OUR BOOK AND VIDEO PAGE FOR SPECIALS!

$50 each

$50 each

$50 each

 

LATHE PINS for turning shafts (5/16-18, 5/16-14, 3/8-10, Cue Tech/ Scorpion style & Radius/ Ball Screw)

UNIVERSAL SHAFT DRIVER (Stainless lathe pin with pointed rubber driver for spinning non standard thread shafts) $25 each

LATHE INSERTS for turning butts (5/16-18, 5/16-14, 3/8-10 & Radius/ Ball Screw)

$12 each

$50 per set

 

     $25 each

 

$12 each

$40 per set

1/2" DRILL CHUCK with #1 or #2 MT or 3/8-24-tpi

$35 each

SMALL CONCAVE LIVE CENTER ( #1 MT )

$45 each

LARGE CONCAVE LIVE CENTER covers entire tip (#1 or #2 MT)

$45 each

SMALL or LARGE CONCAVE LIVE CENTER (3/8 shank)

$35 each

LARGE 1" DIAMETER 60 DEGREE LIVE CENTER (3/8 shank)
$35 each

SMALL DIAMETER LIVE CENTER for cutting shafts (1/2 shank)

OFF-SETTING LIVE CENTER for cutting tapers (#2 or #3 Morse Taper)

OFF-SETTING LIVE CENTER for cutting tapers 3/8" straight shank smaller unit

$30 each

$150 each

$85 each

SHAFT SEALER   $10.00 - 8oz,   $18 - Pint,  $35 - Quart 

 

SHAFT CLEANER    $8.00 - 8oz,   $15 - Pint,  $25 - Quart 

CUE WAX    $8.00 each,   2-Pack  $15,  6-Pack $40   

LATEX TUBING for wrapping pressure around the cue when gluing in inlays or points. 3 foot lengths    $5 each.

POWER FEED AUTO STOP bracket.  It is removable and trips the powerfeed switch when your cutter reaches the place you want it to stop. $40 each (Only for the Deluxe Cue Smith package one powerfeed type.)

POWER FEED AUTO STOP Electronic Type $65

METAL DUST COVER FOR BED. Eliminates getting glue, dust, or finish on bed.        $25

CORING DRILL  .312" x 14" coring, air cooled. Use as first step drill when coring.  1/2" shank     $135

CORING DRILL  .650" x 14" coring, air cooled. Makes coring forearms a breeze.  1/2" shank     $160

CORING DRILL  .775" x 14" coring, air cooled. Makes coring handles a breeze.    1/2" shank     $175

WEIGHT BOLT TAP Extra Long 8" 3/8-16 use .312" drill or coring drill.   $55

6" CARBIDE TIP BORING BAR (with 3/8" round shank) for boring out butt sleeves: $30   

TOOLPOST FOR ABOVE BORING BAR: Quick Change Holder.  $30

6" CARBIDE TIP BORING BAR (with square shank to fit normal toolpost) for boring out butt sleeves: $35                   

MINIATURE SOLID CARBIDE BORING BAR for installing Uni-Loc, Radial pins and boring out ferrules, etc.  $35

 

SELF-CENTERING THREE JAW CHUCK with 3/4-16 thread.

SELF-CENTERING THREE JAW CHUCK with Deluxe thread and large 1.4" bore.

REAR CHUCK FOR METAL LATHE with micro screw adjusting back plate. This chuck is the same 1.4" bore self centering 3 jaw chuck we use on our Deluxe Cue Smith, but it has a special back plate with adjustable centering screws for easy accurate rear spindle mounting on many metal lathes and some cue lathes without additional machining needed.

STEADY REST WITH DELUXE CHUCK mounted on it. 1.4" bore and self centering.

We have the lower height Mid Size type for $175 and the Deluxe height for $200.
We also have them mounted just on the bearing so you can mount it in your metal lathe steady rest or on your wood lathe $150.

$75 each

  $100 each

 

$175 each

 

 

 

COMPOUND CROSS-SLIDE FOR CUE SMITH LATHE (Rotates 360 degrees for cutting short angles)

EXTRA TOP SLIDES: Non-rotating extra top slides $50 each.

$65 each

 

TENON THREADER for Ferrule (5/16-18)

$40 each

TENON THREADER for Stainless Joint (5/8-11) or (5/8-18) your choice.

$45 each

SPUR DRIVER

DREMEL MOUNT FOR CUE SMITH TOOL POST (3/4-12 mount)

$20 each

$30 each

TEN BUTT/JOINT COLLETS 1.378" OD with 10 ID's from .750" to 1.312"

$75 set

SHAFT COLLETS for protecting shaft when in chuck (order 3 for full set)

$3 each

CENTER DRILL SET
$25 each     
CUE SMITH BELTS 2L200 $14 each, 2L140 $10 each, 3M500 $10 each, 3M315 $10 each. PINION GEAR (For use in Handwheel and Power Feed) .223" pinion $8 each, .250" pinion $12 each, .250" hardened pinion $15 each
EXTRA 1/4" TOOL BITS  Standard Right or Left Hand, Round Nose, Boring Bar, Cut Off Tool  $8 each or 10 for $70 mix and match okay

EXTRA TWO-WAY TOOLPOST      $12 Each

EXTRA FOUR-WAY TOOLPOST    holds four different toolbits $30 Each

$12 each

$30 each

CONVERSION KITS FOR LATHES: Call for quote with lathe specifications ready. (Model, Spindle size and threads per inch, etc..)

WRAPPING MOTOR WITH FOOT CONTROL

$125 UP

CROSSFEED FOR WOOD LATHE

$250 each

CUE COTE-Custom Cue Finish! Two part Epoxy based finish.

Does not need to be sprayed on. Can be brushed on then slowly rotated for a few hours to level out. Instructions included!

WATER BASED URETHANE-Custom Cue Finish! Very easy to use. Spray or brush on. Fast dryng. Only 15 minutes between coats.

$45 quart

 

$20 Pint or

$35 Quart

CUE BUFF! (Buffing Material) Buffs most cue finishes including the above.

$15   8oz.

BUTTERFLY and FULL SPLICE MITRE JIG for bandsaws (cuts angles and prongs in turning squares)  $40

VENEER FIXTURE for cutting 45 degree angles on your veneers   $75

(Requires router table or overhead router like shown in Advanced Volume One DVD plus 5/8 or one inch vertical v-bit). Can also be used on a table saw with blade set at 45 degrees)

BLACK EPOXY DYE

$5

THREAD MILLING ATTACHMENT for Deluxe Cue Smith: It has the ability to mill inside and outside threads with the included Dremel Tool and bits. You can make clean threads for carom cues or thread on your, butt plates, joints and ferrules. You can even thread the forearm and handle together without having to tap the threads.

Thread Milling Attachment: Includes Dremel tool, two carbide thread mill bits, and your choice of one thread gear/ belt set:  $575 on Deluxe package #1 and $450 on Deluxe package #2 with leadscrew powerfeed.

Thread choices: 8, 10, 11, 12, 14, 16, 18 and 20 threads per inch. Extra additional thread gear/belt combinations $65 each.

Extra Thread Milling carbide bits are (1/8" shank one internal and one exteral threading bits) $50 each.

AUTOMATIC TIP SHAPER

TIP SHAPING GUIDE & BLADE REST $30

This is a shaping guide for those who prefer to use the utility blade to hand shape the tip.

It has 3 radius guides on the rest. Nickel, Penny and Dime size radiuses.

This takes the guess work out of it and mounts on one side of your tool post.

BELOW BITS $8 each or 10 for $70 mix and match

Larger One Inch Vertical V-Bit for Cutting Point Grooves   $55

Jewelers Saw and 1/4" arbor for parting off joint rings with router $35

Replacement blades $25

1.25" diameter 6 Wing Cutter with 1/4" shank $55

(Use for ultra smooth finish passes on shafts.)

1/8" Collet for using 1/8" endmills in 1/4" router for cutting stitch rings  $10

Home :: About Us :: Contact Us :: Testimonies :: Tell A Friend :: SPECIALS :: Ordering
Inlay Machine :: Cues :: Book & Videos :: Shop Layout :: International Cue Makers Association :: Favorite Links
Accessories : Lathe Supplies : Wood Shop : Ivory  & Inlay Material : Tip Shaper : Tips & Ferrules : Leather Wrap  
Blanks
: Point Blanks & Decorative Parts :: Cue Lathes : Deluxe Cue Smith : Mid -Size Cue Smith : Micro Cue Smith II : Micro Cue Smith III

© 1999 - 2013 Cue Man Billiard Products.  All rights reserved.
Click to report technical problems
Cue lathe cue man lathe custom cue lathe cue smith cue making cue billiard billiards birdseye maple. Hightower cuemaker cuemasters custom cues cue making equipment ivory inlay wood lathe pool stick billiard Cues. Cue maker cuesmith.com cuesmith.com cuesmith cue smith.   Chris hightower hightower cues cue man cueman.com cueman billiards.  Moori or moori tip and moori tips but shaft wood and cue tips or ferrules just pool cue parts and hightower cues international cuemakers association.